Dodge Dart Forum banner
Cancel
Create thread New Garage Forums

Underbody Shield

1 reading
Jump to Latest
41 - 57 of 57 Posts
#43 ·
Justin Spicer said:
I have the same car sxt I am looking for one as well let's hope it is reasonable priced. You can buy the original one for $180 online. The dealership wanted almost $500😲
Click to expand...
I shredded my factory covers on I-95 with an Alligator (truck tire piece) laying in the road.

Reasonably priced? Well, that's subjective, what is not subjective are the benefits of this complete belly pan. Made of Polypropylene which has a high heat tolerance, resistance to cracking, and damage due to impact. This kit offers better aerodynamics (Deyeme notation) which makes sense considering its installed profile. It is not invincible but worth every dollar to me and it has saved me.

The OEM Closeout Panel is made of Polyethylene which is basically the antithesis, and the so called belly pan is made of fiberglass. Good grief.

When my car is in the air I typically find a few Technicians standing around staring upward and pointing. That's when I pop up and provide "best use instructions". I would never deign to consider myself a Technician but there are best use instructions! There are two doors just as the OEM materials have. The OEM doors pop open by pressing a latch and pulling the door off. The custom cover uses two stainless steel screws for each door. If you take both screws out it is a hassle to get them back in. Instead loosen one screw and remove the other allowing you to swing the door out of the way.

I hope this helps anyone looking for more detail.
 
#45 ·
Just got my Deyeme underbody shield ordered. Money and time availability have finally crossed paths! Looks like I'll get to install this at the same time that I'm replacing the AGS connector, as it looks like the body shop that repaired my bumper a couple years ago nicked the wire jacket and it slowly corroded until failure recently. I'd hold them to it, but they went out of business at the start of last year... They did good body work, but were absolutely hell on my wiring.
 
#46 ·
Zeprider said:
I shredded my factory covers on I-95 with an Alligator (truck tire piece) laying in the road.

Reasonably priced? Well, that's subjective, what is not subjective are the benefits of this complete belly pan. Made of Polypropylene which has a high heat tolerance, resistance to cracking, and damage due to impact. This kit offers better aerodynamics (Deyeme notation) which makes sense considering its installed profile. It is not invincible but worth every dollar to me and it has saved me.

The OEM Closeout Panel is made of Polyethylene which is basically the antithesis, and the so called belly pan is made of fiberglass. Good grief.

When my car is in the air I typically find a few Technicians standing around staring upward and pointing. That's when I pop up and provide "best use instructions". I would never deign to consider myself a Technician but there are best use instructions! There are two doors just as the OEM materials have. The OEM doors pop open by pressing a latch and pulling the door off. The custom cover uses two stainless steel screws for each door. If you take both screws out it is a hassle to get them back in. Instead loosen one screw and remove the other allowing you to swing the door out of the way.

I hope this helps anyone looking for more detail.
Click to expand...
Well, you sold me!! I just replaced the head gasket ( 107,000 miles) couldn't believe it. I am finishing up I definitely need to get these closeout panels for my dart. Do you have a link to purchase? Thanks
 
#49 ·
CanadianGuitar said:
Everything will be fine. You might lose a bit of MPG since it changes the airflow underneath the car, and in the very long run could see a bit extra wear/tear on the car as it would let more water and other stuff on the run into the bottom of your engine bay, but really, it's kind of minor stuff depending on your perspective.



Edit: That being said, if you wanted a new one, the part is 68082724AH. The cheapest place I could find it during a 3 minute google was the site I would of recommended anyway https://parts.allmoparparts.com/oem-parts/mopar-under-body-shield-68082724ah/?c=Zz1ib2R5JnM9c3BsYXNoLXNoaWVsZHMmaT1QSzEzMDQ1NSZyPTQmYT1kb2RnZSZvPWRhcnQmeT0yMDEzJnQ9c3h0JmU9MS00bC1sNC1nYXM= / https://parts.allmoparparts.com/aut...xt-trim/1-4l-l4-gas-engine/body-cat/splash-shields-scat/?part_number=68082724ah158 bucks if you wanted to replace it with a new one.
Click to expand...
Hi so the part # 68082724AH that is for the under carriage shield for a dodge dart 2016? Someone I guess tried to steal my catalytic converter and completely tore it up so that it looked like it was folded in half and the auto shop took it off for me so it would stop dragging but I need to replace it. I now have nothing protecting the bottom of my engine? sorry not good at car talk.
 
#50 ·
68082724AH is the correct part number for the belly pan for all years of Darts. The closeout panel is the part right behind the bumper and there are several possible numbers:
68155070AD
68185904AE
68191423AD

If your shop discarded the fasteners this is that number for each bolt:
6508332AA

You can send an email to Benny with a VIN number to confirm numbers.
sales@AllMoparParts.com

Your insurance might cover the cost if this was actually a theft attempt.
 
Save
Reply Quote Like Like
#51 ·
DeyemeRacing said:
Do it one better. The OE pieces hang way down at the radiator support. The one I designed sits a little closer, and is made of very durable polycarbonate. The belly pan (the large, more rectangular piece) has aluminum reinforcements at some of the attaching points. All OE attachment points are used, and new hardware is included. Also, we make 'em in clear and white, in addition to black, if you want to see what's up in there from underneath or just hide LEDs in there to shine down like we did with our project car.
Image
As you get it - 2 pieces w/ doors for oil plug and (2.0/2.4 only) oil filter. Integrated aluminum louvered heat shield, just like the stock piece, too.
Image
Installed on Speedy G, our project car (BrightWhite, with amber LEDs from SuperBrightLEDs)
Image
Click to expand...
I have this. But now I need replacement hardware and clips. Can I order these on your website or will any Hardware store stainless steel clips work? thanks need asap
 
#53 ·
crystalmjensen22 said:
How can I order this?
Click to expand...
Appears to be discontinued. It's isn't listed under products for a Dodge Dart at the Deyeme Racing site.

The belly pan and closeout panels are still available from Mopar sites and dealers.
68082724AH
68155070AD
68185904AE
68191423AD
Be sure to give your VIN so you get the correct closeout panel.
 
Save
Reply Quote Like Like
#54 ·
Yeah, not sure if the DeyemeRacing covers are available. I bought them years ago; they made WAY too much noise. I eventually replaced them with factory covers. Then, I ran over something. I have a new closeout and belly pan sitting in the closet. Tired of buying and replacing them.
 
41 - 57 of 57 Posts
About this Discussion
56 Replies
23 Participants
Last post:
Midnight Rider
Dodge Dart Forum
posts
534K
members
34K
Since
2012
Dodge-Dart.org is a forum dedicated to the 2013-2016 Dodge Dart. Join and participate in discussions about maintenance, performance mods, and mechanical issues. Get the latest tips, news, browse the classifieds, and more!
Full Forum Listing
Explore Our Forums
Dodge Dart General Discussion Dodge Dart 1.4L MultiAir Turbo New Member Introduction Dodge Dart Electronics and Audio Dodge Dart Mechanical Problems