[The_lishp]

Rios by chance would you know if factory darts with bcms have fuses for the left and right headlight in fuse location 13 and 93 respectively?

 

[alpinegreenneon]

Only Darts with factory HIDs had BCMs with headlight fuses F13 and F93.

 

[The_lishp]

Thank you that's all I was hoping to find out by the way alpine your right bootmode is through connector pins but it needs a resistor so it needs to be opened unfortunately

 

[The_lishp]

ALSO THIS WOULDNT HAPPEN TO BE THE FUSE SET UP FOR HIDS BY CHANCE WOULD IT? I'm thinking used bcm if I can't figure out how to get it to mine with halogen set up to play nice with my new hids gonna be taking it out tomorrow after I'm done soldering some resistors hopefully all goes well just finished my headers gonna take some work lol

 

[The_lishp]

Not sure why but they work no bcm or fuse the headlight on the right no bulb but works lol left flashes but I think it's wiring the hid bulb is fine

 

[The_lishp]

I ordered a used hid bcm but just curious when someone who has alfa obd nd hids has time will they check under headlamp type and let me know what there setting is if it's not been messed with mine was type 1 I believe lol not good at remembering to save I screen shot it gets messy thanks 😉

 

[alpinegreenneon]

You will likely get a VIN mismatch code for the used BCM. As far as I know, it isn't possible to rewrite the VIN on a used BCM.

 

[The_lishp]

Hopefully it will sort its self out so is it safe to use hids without the right bcm? Cause the one I have installed is turning on the second one arrives today

 

[The_lishp]

So I'm back at halogen and need to swap bcms back the hologen have a bcm and the hid have only hid I can't turn off xenon lights due to parameters on my ecu it says 🤔

 

[R&D Guy]

@The_lishp are you just trying to run HID's?

 

[RSR00789]

Hey sorry busy few days so I'm sat down next to my car and thus is the wiring I'm looking at I have the ballast plugged into the harness from the light I'm only confused about the green connector wire that is coming off the ballast everything else is plugged in

What kind of ballast is that, and where did you buy it? I sent a post but it looks like you have already covered it....I got the exact same port that the ballast will go to...

 

[The_lishp]

I got the ballast off of ebay word of cation I've figured it possible but if your upgrading from halogen to hid you will also need a used bcm that is specific for hid as our bcm doesn't even have the ability to put fuses into the required slots when you replace bcm with a used one under rf hub in alfa obd do the bcm relearn procedure and you should be set

 

[R&D Guy]

I got the ballast off of ebay word of cation I've figured it possible but if your upgrading from halogen to hid you will also need a used bcm that is specific for hid as our bcm doesn't even have the ability to put fuses into the required slots when you replace bcm with a used one under rf hub in alfa obd do the bcm relearn procedure and you should be set

Yes, you would need a BCM that is for HID headlights. or if you can reprogram the BCM with AlfaOBD program.

 

[The_lishp]

The Darts with stock halogens have different body computers I went back ti halogen due to the bcm being apain to install lol but I got all the stuff one day but for stock halogen bcm the clip for holding the 20 Amp fuse for the xenon bulbs is missing the fuses just slip right out

 

[The_lishp]

Wait I'm confused your agreeing with me ain't you lol honestly wouldn't had ever figured out half of that Instal without your help thanks

 

[R&D Guy]

Wait I'm confused your agreeing with me ain't you lol honestly wouldn't had ever figured out half of that Instal without your help thanks

We all MOD this car, and when someone tell's you it can't be done. to me, it just means it can't be done that way. but there are always other way's.
and Yes the BCM for vehicles that come with Halogen lights have the location for the fuse, but no fuse because there is no nothing that plugs to that fuse, as you know know that BCM does not have the electric circuit.